TCL L47V6500A-3D 打印信息我翻译是总线开关问题，请高手帮我解读。

新兴电子

2017-11-9, 9:38:42
COM4, BaudRate:115200 bps, RXD: VGA->12,TXD: VGA->15, Printed by RT809F:

夿IST OK
BIST OK
ALL BIST OK!!
[3456789A][3456789AB][3456789A][456789AB] 6767
[0123456789ABCDEF][0123456789ABCDEF][23456789AB][3456789ABCD] 7768
HAL_MIU_INIT2
Hello PM51...
Hello Main
MDrv_BDMA_Init OK..
bdma start .......
wait done.......
Bdma is done!
run code in dram
Start to reset MIPS

End of MIPS init

HAL_MB_Unmask_Cpu3_2_Cpu0
UART_115200__D


U-Boot 2011.06-svn19964 (May 20 2016 - 15:42:08)


CPU  : AMBER3
Board: BD_MS801_MAA2XG
DRAM:  256 MiB
SPI:  Flash is detected (0x0711, 0xEF, 0x40, 0x15)
MDrv_SERFLASH_GetInfo()
        u32AccessWidth = 1
        u32TotalSize   = 2097152
        u32SecNum      = 32
        u32SecSize     = 65536
spi_init: cfg_env_offset: 0x1e0000, at 552
MMC:   mstar-emmc: 0, 0 blocks
Flash is detected (0x0711, 0xEF, 0x40, 0x15)
MDrv_SERFLASH_GetInfo()
        u32AccessWidth = 1
        u32TotalSize   = 2097152
        u32SecNum      = 32
        u32SecSize     = 65536
read_spi_dbtable success...>>>
read table >>>
logo  offset[0x00180028] size[0x0001c2e1] end[0x0019c309]
music offset[0x0019c309] size[0x00000000] end[0x0019c309]
panel offset[0x0019c309] size[0x0000005c] end[0x0019c365]
ursa  offset[0x0019c365] size[0x00000024] end[0x0019c389]
keypad  offset[0x0019c389] size[0x00005000] end[0x001a1389]
db_checksum =:0x4ea5900e
save db_checksum =:0x4ea5900e
db_table.keypad_offset =:0x19c389...db_table.keypad_size=:0x5000
Read_PanelParaFromSpiflash success...>>>


UART BUS OFF!!_MApi_PM_ProcessPmInit >> MDrv_PM_Init

avlink_init done
power down
enable WDT
HAL_PM_WakeupFromZero
Run code in SPI.......
蕡ˇ煃偀┊?倡煟暗朝矡兏祼崅BIST OK
BIST OK
ALL BIST OK!!
[3456789A][3456789AB][3456789A][456789AB] 6767
[0123456789ABCDEF][0123456789ABCDEF][3456789AB][3456789ABCD] 7778
HAL_MIU_INIT2
MDrv_BDMA_Init OK..
bdma start .......
wait done.......
Bdma is done!
run code in dram
Start to reset MIPS

End of MIPS init

bring up MIPS over


UART_115200__D


U-Boot 2011.06-svn19964 (May 20 2016 - 15:42:08)


CPU  : AMBER3
Board: BD_MS801_MAA2XG
DRAM:  256 MiB
SPI:  Flash is detected (0x0711, 0xEF, 0x40, 0x15)
MDrv_SERFLASH_GetInfo()
        u32AccessWidth = 1
        u32TotalSize   = 2097152
        u32SecNum      = 32
        u32SecSize     = 65536
spi_init: cfg_env_offset: 0x1e0000, at 552
MMC:   mstar-emmc: 0, 0 blocks
Flash is detected (0x0711, 0xEF, 0x40, 0x15)
MDrv_SERFLASH_GetInfo()
        u32AccessWidth = 1
        u32TotalSize   = 2097152
        u32SecNum      = 32
        u32SecSize     = 65536
read_spi_dbtable success...>>>
read table >>>
logo  offset[0x00180028] size[0x0001c2e1] end[0x0019c309]
music offset[0x0019c309] size[0x00000000] end[0x0019c309]
panel offset[0x0019c309] size[0x0000005c] end[0x0019c365]
ursa  offset[0x0019c365] size[0x00000024] end[0x0019c389]
keypad  offset[0x0019c389] size[0x00005000] end[0x001a1389]
db_checksum =:0x4ea5900e
save db_checksum =:0x4ea5900e
db_table.keypad_offset =:0x19c389...db_table.keypad_size=:0x5000
Read_PanelParaFromSpiflash success...>>>


UART BUS OFF!!

DongBeide

去809H的QQ群交流 ，或在群里找客服张技工交流